Flush toilets often with unclean water to save water.
I thought, no matter how dirty the water is, it's better than the toilet!Flushing the toilet with sewage, isn't it killing two birds with one stone?But the other day, when I went to deliver water to the nanny, I happened to run into the nanny who was sweeping the floor.
"No!”
Aunt said,Flushing the toilet directly with water may seem like a cost-effective solution, but "I'm afraid it's not something I can afford."
There is not enough water to form a rainbow suction
When I heard that you can't pour water into the toilet, I couldn't believe it, and in my memory, my mom used unclean water to flush the toilet. However, the aunt said that the toilet is not the same as before.
"It used to be a straight rush, but this time it was changed to a siphon type. ”
The water pipe in the flush toilet is straight, so the water flow is used to flush the toilet, of course, there will be no problems. However, the siphon toilet is cleaned with rainbow suction.
Siphon force simulation test.
One of the most important factors is to fill all the curved pipes in the toilet. If it's not filled, there's no rainbow suctionThe water will flow slowly along one side of the pipe, which is called "not clean".
.02 DefenseThe depth of the water is insufficient
If it's just "not flushing", I'm okay with it, because there's nothing in the toilet, I just flush the toilet again. But my aunt said to me:
"After the water is released, there is no rainbow suction, which will cause a lack of water pressure. ”
Generally, there will be a small amount of water at the bottom of the toilet, which is called a "water seal". We can click on the flush button and see how the water seal is formed
You see, the water seal was the first to disappear. It has to do with the water pipes in the toilet.
At this time, the water is siphoned into the red circle, and when the rainbow suction disappears, it returns to the water trap and becomes a water seal.
If you pour water directly, the amount of water is insufficient, and the siphon force is slightly weak, but there will still be. The siphon force will suck all the water away, and there will be no water backflow, and the seal of the water will be lost.
What would happen without the seal?Taste regurgitation, mosquito bites, etc., will be produced. Aunt said
"When we train, we all pour water into the toilet, so when we train, we all get the water back in the right place. ”
The interior walls were not cleaned
Can pouring water really clean the toilet?Aunt said,It accurately removes dirt from the inner wallsHowever, if it is only used to "flush the toilet", it is better to flush directly.
You can look at the toilet spouts, some are breathable, some are rotary.
The goal of these two drainage methods is to swirl the water through the inner wall of the toilet. SnailsThe swirling stream flushes every inch of the pipe, i.e. there are no cleaning blind spots.
But if you pour the water directly, it's different. In some places, there is no water at all, and over time, bacteria will grow.
How to use a toilet that saves water?
So, I took this opportunity to ask you for some practical ways to save water. The housekeeper told me that there was not much she could do about it, and said:
"Normally, the volume of the flush toilet is 55 liters, so it's not much waste. ”
However, if you are really stingy, you can try the following three methods.
Open the toilet lid and identify the parts with a higher water level. On one side, there is a plastic buckle that can be lowered by pressing it down slightly. The lower the buckle, the less water will be in the reservoir.
In this way, the volume of the tank is reduced, and the amount of water required for each flush is also reduced. But don't forget to rinse it after the first adjustment to see if the height of the water seal is more than 55 mm, so that there will be no aftertaste due to too little water.
Some toilets have two buttons on the tank, one is large and the other is small, and it is not recommended to adjust such a tank. Normally, at the touch of a small button, half of the water in the tank is drained, thus saving water.
The reason why adjusting the water level is not recommended is because we can keep the large buttons for a rainy day. High water levels can also be used when the toilet is slightly clogged or needs to be cleaned.
Clean the toilet pipes regularly, usually by pouring a bottle of detergent into the toilet bowl and pouring a cup of hot water into it. The unclogging agent can dissolve all the dirt on the inner wall of the toilet bowl and keep the toilet bowl open.
The same goes for white vinegar with baking soda.
Siphon toilets have very strict requirements for water pipes, and many users report that the suction power of their toilets is not as great as when they first bought them, in fact, this is due to a slight blockage of the water pipes. As long as the water pipes are cleaned and drained, a lot of flushing water can be saved.