Safety helmet manufacturers can apply for LA labor safety certification.
First, the product technical requirements.
1.Hoops. The cap band should be adjusted according to the applicable head circumference size as indicated in the helmet identification.
2.Sweatbands.
The area corresponding to the forehead of the hat band should have sweat-absorbing fabric or add sweat-absorbing bands, and the width of the sweat-absorbing bands should not be less than the width of the hat band.
3.Chin strap size.
If the helmet has a chin strap, a webbing with a width of not less than 10 mm or a rope with a diameter of not less than 5 mm should be used.
4.Cap shells. The surface of the cap must not contain air bubbles, defects or other defects that impair performance.
5.Component mounting.
The installation of each part of the safety helmet should be firm, and there should be no loosening or slipping.
6.Quality (excluding accessories).
Special type safety helmets should not exceed 600g;Ordinary safety helmets should not exceed 430g;The relative error between the actual quality of the product and the quality of the mark should not be greater than 5%.
7.Visor. The visor should be 70 mm according to the method specified in GB T 2812.
8.Brim. According to the method test specified in GB T2812, the brim should be 70mm.
9.Wearing height.
According to the method specified in GB T2812, the wearing height should be 80mm.
10.Vertical spacing.
According to the method specified in GB T2812, the vertical spacing should be 50mm.
11.Horizontal spacing.
According to the method specified in GB T2812, the horizontal spacing should be 6mm.
12.Protrusions inside the cap shell.
The presence of sharp protrusions between the inside of the shell and the liner must not exceed 6 mm in height and should be covered with soft padding.
13.Venthole.
When the cap shell has a vent, the total area of the vent should not be greater than 450mm.
14.Chin strap strength.
When the helmet has a lower frequency band, according to the method specified in GB T2812, the force value of the chin band when it is damaged should be between 150 N and 250 N.
15.Annex.
When the helmet is equipped with accessories (such as protective face shields, hearing protectors, lighting devices, communication equipment, warning signs, information devices, etc.), the accessories should not affect the wearing stability of the helmet, and at the same time do not affect its normal protective function.
16.Shock absorption performance.
According to the method specified in GB T 2812 test, after high temperature (50 s2), low temperature (-10 s2), immersion (water temperature 20 s2), ultraviolet irradiation pretreatment after impact test, the force transmitted to the head mold should not be greater than 4 900 N, and the cap shell should not have fragments falling off.
17.Puncture resistance.
According to the method test specified in GB T 2812, after high temperature (50 s2), low temperature (-10 s2), water immersion (water temperature 20 s2), ultraviolet irradiation pretreatment after puncture test, the steel cone shall not touch the surface of the headform, and the cap shell shall not have fragments falling off.
2. Documents need to be prepared.
1. The original and copy of the business license of the enterprise (if the applicant unit holds the unincorporated "business license" application, the original and copy of the business license of the legal entity shall be submitted at the same time);
2. Proof of ownership and right of use of production sites (real estate certificate, land use right certificate, lease contract, certificate of shared property rights of large state-owned enterprises, certificate of self-construction of rural homesteads);
3. Management responsibilities.
3.1. Quality management organization chart;
3.2. The responsibilities, authority and assessment methods of all levels and types of personnel.
4. Equipment management.
4.1. Production equipment management system;
4.2. Production equipment operating procedures;
4.3. Production equipment maintenance plan;
4.4. Process equipment management system;
4.5. Management system of testing and inspection instruments and equipment.
4.6. Safety protection performance testing and inspection equipment operating procedures;
4.7. Testing and inspection equipment verification plan and verification certificate;
4.8. Production equipment, process equipment, inspection instruments and equipment ledger.
5. Document management.
5.1. Document management system;
5.2. Procedures for the identification and circulation of foreign documents;
5.3. Catalogue of laws, regulations and rules related to production and business activities;
5.4. The national standards, industry standards, relevant standard catalogs and standard covers implemented by the production of products;
5.5. Product design drawing;
5.6. List of main raw materials;
5.7. Summary table of parts, standard parts, outsourced parts and purchased parts;
5.8. Process flow diagram;
5.9. Inspection standards for raw materials;
5.10. Application for product safety protection performance inspection procedures;
5.11. Product Instruction Manual;
5.12. Factory certificate;
5.13. Product trademark registration certificate (if there is no registered trademark, this item is missing);
5.14 products**.
6. Quality control.
6.1. Procurement control system for raw and auxiliary materials, parts, outsourcing parts and purchased parts;
6.2. Supplier evaluation provisions;
6.3. Specific provisions on the acceptance of raw and auxiliary materials, parts, outsourcing parts and purchased parts;
6.4. Process management system and assessment methods;
6.5. Control measures for quality control points;
6.6. Product factory inspection system;
6.7. Nonconforming product management system;
6.8. Warehouse management system.
7. Personnel assessment.
7.1. Safety protection performance inspection personnel certificate (training certificate);
7.2. Proof of participation in safety production training by the person in charge of the enterprise and the safety production management personnel.
8. Safe production.
8.1. Safety production policy and objectives;
8.2. Regulations on the management of safety production objectives;
8.3. Identification and application of safety production laws and regulations;
8.4. Safety production rules and regulations;
8.5. Occupational hazard and occupational disease control system.
3. Certification process.
Application - preliminary review and acceptance - technical review - on-site review - product inspection - review and issuance of certificates - post-certification supervision.
Fourth, the certificate query method.
LA Certification
Can labor protection products OEM manufacturing (processing) enterprises apply for LA certification?
Gas cylinder filling inspection and recording, mobile pressure vessel gas cylinder filling license processing.