"Just wrap a little more electrician's tape, and you will fire me, I don't accept it! The electrician said with some grievances
Because of the extra wrapping of electrical tape, Master Liu, an electrician who was still in the probationary period, was fired by the factory director, and then arranged for his relatives to come over to take over, but no one spoke to the electrician, what the hell is going on?
Master Liu has just come over, and there is an electrician in the factory, Master Li, because the factory has recently added two plastic pipe production lines, and an electrician master in the factory is relatively busy, and then the production line has to be added to add an electrician master.
In the second week when Master Liu came to work, the talent of the machine manufacturer went to the factory to start the installation, because Master Liu had just arrived, and the factory director arranged for Master Liu to assist in the installation, and Master Li continued to see the original production line, in fact, there was nothing to do, in fact, it was supervision, and there was no need to work.
After the installation is completed, the people of the machine manufacturer have left after the test, because the machine manufacturer has been busy recently, to install, the final power supply and wire arrangement, have been handed over to Master Liu, these things as an electrician Master Liu is naturally easy to deal with, Master Liu has 6 years of experience as an electrician in the factory.
At the beginning, there were a total of 8 people who came to interview with Master Liu, including a relative of the factory director, after comprehensive consideration of personnel, only Master Liu was finally selected, if there was no Master Liu, the relatives of the factory director should be left behind, the factory director's relatives are not bad in technology, that is, the working hours are less than Master Liu.
After an afternoon of finishing work, the new production line can finally be put into production, and now the time is almost to get off work, so we can only start running again tomorrow.
The next day, Master Liu came early, and waited for the production line staff to transport the materials to start the machine, everything was ready, and the factory director also came to see it, and the machine was running normally after starting, to say that the new equipment is different, and the production efficiency is much faster than the old machine.
In this way, the production performance of our employees is better, when everyone is happy, the machine that has been running for less than half an hour has failed, and it has automatically stopped, everyone is stunned, what is the situation, the new machine is only used to break down?
Master Liu immediately went to check it, the parts were not damaged, and the line was normal, and then went to look at the machine display screen, which showed a string of red English **, Master Liu went to find the machine manual, and only after a comparison did he know that it was a current fault.
Master Liu started to check again, there was still no problem, the factory director was also anxious on the side, and the production would be increased in a few days, why was the new machine so unreliable, and he hurriedly called someone to call Master Li.
The two masters found the instrument and then checked the machine inside and out, back and forth several times, did not find the problem, the current and voltage in the factory has been very stable, that is only the problem of the machine, but obviously yesterday the machine manufacturers have tried to operate normally.
In the end, there was no way, the factory director could only call the person from the machine manufacturer, and after asking a circle, all kinds of possible problems were investigated, but it still didn't work.
The factory director questioned that there was a problem with the new machine, and immediately asked the machine manufacturer to send someone to deal with it, if it could not deal with the loss of the factory in time, it would go through legal procedures in accordance with the contract signed at the beginning, and the machine manufacturer should be compensated.
However, the machine manufacturer can not immediately send personnel, and now the machine manufacturer has too many orders to install after-sales, and the machine manufacturer can only think of a way to communicate with each other, and think of many possibilities for machine problems, which can not be solved one by one.
Just when the two sides were at a stalemate, on the morning of the third day, the machine manufacturer rushed over, these two workers happened to be in a nearby city, and drove here overnight after finishing the order, they should not have come over, they still have the next order to continue, but there is no way, there is a problem here can only be rescued first.
The two staff members came to check the motor of the machine, and the colleagues who installed it in front also said that there was no problem at that time, so they checked the motor first, a machine has 4 motors, which is the accessory with the largest electricity consumption, and the current failure may be a problem with the motor, and checked it with a professional instrument, and personally dismantled the motor, carefully tested the internal coil line of the motor, and spent most of the day, and could not find any problem at all.
Then continue to check all kinds of setting parameters, electronic components, and circuits, and after a while, it can be said that there is no problem with this machine, so why is there a shutdown failure, which makes them have a headache.
Next, the staff started the machine for trial operation, and used the instrument to test the current of the machine when it was running, and found that the current would have a large deviation in the current correlation index when it was ready to shut down.
So after the power was off, I disassembled the main control switch box, and I found nothing after checking, it was normal, and there was no solution this time.
Just when the staff was about to give up, they suddenly found that a copper nose connection wire on the switch was wrapped with a lot of electrical tape, and even some were wrapped in the wiring screws.
The staff disassembled the adhesive tape, and then tested the machine, the previous question of the current was gone, and told the factory director about it, indicating that it was not the machine that had a problem, but the electrician in your factory would not be wired, and this matter was handled here.
The staff of the machine manufacturer also reported the matter to the company, and the leader of the machine manufacturer called **, found the factory director and asked to be responsible for the maintenance fee, as well as the negative impact of this incident on the machine manufacturer to apologize.
It turned out that this incident was only a few days ago, and it spread all over the industry circle, and many companies knew about it, which is bound to have an impact on the company.
Just when the factory was trying to solve the problem, the factory director directly fired Master Liu, because the junction box was in charge of Master Liu, of course Master Liu was not convinced, and directly said: "Just wrap a little more electrical tape, you will fire me, I don't accept it." The tone also seemed aggrieved.
The factory director smiled after hearing this, and responded: "Master Liu, is this a little bit of a problem with electrical tape?" This is a low-level mistake, an electrician with 6 years of work experience should not make it, do you know how much impact this has on the factory, you are not suitable to work here, go to the finance to get a salary and go. ”
Then the factory director recruited his relatives the next day, and then the factory director arranged for Master Li in the factory to take his relatives to work together, so as to be familiar with everything in the factory, so as to avoid further problems.