As a common drinking equipment in homes and businesses, Angel water dispenser is widely recognized by users for its stability and durability. However, even high-quality water dispensers may experience some glitches. This article will provide you with the common faults of Angel water dispenser and the corresponding maintenance methods to help you quickly solve the problem and ensure the normal use of the water dispenser.
1. Common faults and maintenance methods
Water leakage problems
Fault manifestations: There are traces of water at the bottom of the water dispenser, or there are water droplets at the connection between the bucket and the water dispenser.
Repair methodFirst, check whether the bucket is installed correctly and confirm that the sealing ring of the bucket is intact. If the bucket is installed correctly and the seal is intact, there may be a leak in the pipes or fittings inside the water dispenser. At this time, it is necessary to disassemble the water dispenser shell, check whether the water pipes and joints are aged or loose, and replace or tighten them in time if the parts are aged or loose.
No water or little water output
Fault manifestations: When the water dispenser is pressed, the water dispenser does not produce water or the water output is very small.
Repair method: First, check whether the power is turned on and whether the power switch is turned on. If the power supply is normal, it may be that the pump is damaged or the water pipe is blocked. At this time, you need to disassemble the water dispenser shell, check whether the pump is working normally, if the pump is damaged, the pump needs to be replaced; At the same time, check whether the water pipe is blocked, and if there is a blockage, the water pipe needs to be cleaned.
The heating function is ineffective
Fault manifestations: The water dispenser does not heat up or heats up slowly.
Repair methodFirst, check whether the heating tube is damaged, if there is any damage to the parts, it needs to be replaced in time. If the heating tube is normal, the thermostat may be damaged, and the thermostat needs to be replaced. In addition, it is necessary to check whether the power cord is in poor contact or open circuit, and if there is any bad contact or open circuit, the power cord needs to be rewired or replaced.
The refrigeration function fails
Fault manifestations: The refrigeration function of the water dispenser does not work properly, or the refrigeration speed is slow.
Repair methodFirst of all, check whether the compressor is working properly, if there is any damage to the parts, it needs to be replaced in time. If the compressor is normal, it may be that the condenser or evaporator is dirty, and the condenser and evaporator need to be cleaned. In addition, it is necessary to check whether the refrigerant is sufficient, and if it is insufficient, it is necessary to replenish the refrigerant.
The indicator light is not on
Fault manifestations: The indicator light of the water dispenser does not light up, and the working status cannot be displayed normally.
Repair methodFirst, check that the power plug is plugged in tightly and that the power switch is turned on. If the power supply is normal, it may be a damaged indicator or a faulty circuit board. At this point, the indicator or circuit board needs to be replaced.
2. Measures to prevent failures
Clean regularly: Clean the casing and waterway system of the water dispenser regularly to avoid the accumulation of dust and dirt. At the same time, the filter cartridge should be replaced regularly to ensure the quality of drinking water.
Avoid frequent switching: Try to avoid turning the water dispenser on and off frequently to reduce wear and tear on the internal components.
Be aware of the usage environment: Place the water dispenser in a ventilated and dry place, away from direct sunlight and humid environments.
Regular check-upsRegularly check whether the power cord, water pipe and other parts of the water dispenser are in good condition, and replace them in time if they are aging or damaged.
3. Maintenance precautions
Safety first: Before carrying out repairs, it is important to ensure that the power supply is disconnected to avoid electric shock.
Use specialized tools: When disassembling and installing parts, use special tools to avoid damage to other parts.
Follow the instructions: When replacing parts, be sure to follow the operating steps in the instructions to ensure proper installation.
Keep it clean: During the maintenance process, pay attention to keep your hands and working environment clean to avoid dust and dirt from entering the inside of the water dispenser.
IV. Conclusion
Through the introduction of this article, I believe you have a more comprehensive understanding of the common faults and maintenance methods of Angel water dispensers. In the actual use process, if you encounter problems, you can troubleshoot and repair them according to the maintenance methods provided in this article. At the same time, it is recommended that users regularly maintain and maintain the water dispenser to prolong its service life and ensure the safety of drinking water.
Angel water purifier