Door and window openings are transformed.
Convert the name and size data of the door and window hole in CAD** into the name and definition of the door and window hole in the model, which is used for the subsequent [Door and Window Hole Conversion] function to generate the door and window hole entity.
Procedure
On the tab, select [Dawn BIM Replication], and click [Door and Window Hole Table Conversion] to pop up the conversion interface;
Box selection**Extract the data of the door and window hole table, and check it according to the identification information of the box selection;
Select Conversions. 
2-1 Door and window opening surface conversion (front).
2-2 Door and window surface conversion (rear).
Frequently Asked Questions
Can the bottom height of the window be identified together when identifying the door and window openings?
Re: Yes, there is information about the bottom height parameter of the window in the door and window opening table, which will be displayed in the recognition result.
2-3 Identification results.
After the conversion of the door and window table, there is no corresponding size information in the recognition result, is there no successful conversion?
Reply: Extract the result column to confirm whether there is any corresponding size information for the opening size in the first row.
2-4 Comparison of before and after extracting sizes.
2. Conversion of door and window holes
According to the CAD door and window hole layer, the door and window hole component entity is converted, and the door and window hole table should be converted before the door and window hole is identified.
Procedure
On the tab, select [Dawn BIM Molding], and click [Door and Window Hole Conversion] to pop up the conversion interface
Click [Settings] in the lower left corner to set the door and window identifier;
Extract the corresponding label and edge layers
Select how you want to convert.
2-5 Door and window openings are converted (front).
2-6 Door and window hole conversion (rear).
Frequently Asked Questions
How to deal with the conversion of extracting the layer of door and window openings to 0?
Re: Is there a way to extract and convert the door and window hole table first?
The drawing is named the security door, can the software turn over the style of the security door?
Re: The software does not support the actual style of the anti-theft door for the time being, and the naming of the components after the mold is consistent with the naming of the drawing, and there is no problem with the engineering quantity.
3. Generate floor slabs
According to certain rules, the cast-in-place slab is automatically and quickly generated.
Procedure
New slab type;(Note: It can be named according to the actual floor slab to facilitate the identification of engineering quantities).
Select the rules and layout of the generated board;
Select the corresponding generation method.
2-7 Generate the floor slab (front).
2-8 Generate the floor slab (rear).
Frequently Asked Questions
Will the software judge and identify the settling plate during the turning process?
Re: It will automatically determine whether it settles according to the annotation of the drawing.
Will the board hole line be automatically judged and recognized?
Re: Yes, after selecting the drawing to extract the hole line by identifying the layout, the software will make a judgment based on the extracted hole line layer.
2-9 Extract the plate hole line.
4. The lifting plate is connected
When there is a height difference in the cast-in-place slab, it is set according to the drawing instructions.
Procedure
Select the function and select the two cast-in-place slabs that need to be connected;
Set the size parameters of the lifter plate connection;
Generate the component when determined.
2-10 Lifting plate connection (before arrangement).
2-11 Lifting plate connection (after arrangement).
Frequently Asked Questions
When using the function, the prompt indicates that the component is not classified, and the function cannot be used
Re: The selected slabs need to be classified as cast-in-place slabs.
In the process of using the function, it always feels difficult to use, and sometimes the layout is not successful
Re: Check yourself before using the function: whether the projection lines of the two boards overlap the edge of the board, in layman's terms: there is tangent when you look at it from above;Whether the top and bottom surfaces of the two slabs are of different heights, and at least one of the faces has a height difference.