The charging head network purchased the fill light of the Insta360 Flow mobile phone gimbal, which is fixed to the mobile phone clamp through the built-in buckle, and can be used by connecting to the Type-C power supply port of the gimbal. The fill light uses RA95 high color rendering image-level lamp beads, which restore 95% of natural sunlight and provide true color reproduction.
The fill light also has three color temperature modes, warm and cold, and mixed, with three brightness levels to choose from, for a total of nine combinations. And it supports forward and backward rotation to meet the needs of different usage scenarios. Let's take a look at the interior design and materials of the Insta360 Flow mobile phone gimbal fill light.
Spotlight, product exterior and Insta360 Flow are printed on the front of the box, and the bottom is accented with a red color scheme.
Close-up of the product information on the back, the model is CINSBBBA, and the manufacturer is Yingshi Innovation Technology Co., Ltd. *** The product has passed CE, FCC, UKCA certification.
In addition to the Insta360 Flow fill light itself, there is also an instruction manual in the package.
The structure of the Insta360 Flow fill light is composed of a fill light, a metal fixing clip and an extended USB-C**, the overall design is very small and lightweight, which is easy for users to assemble and use, and the strength is also ***
The surface of the USB-C cable head housing is matte for easy plugging and unplugging, and it is also designed with Insta360.
Close-up of the inside of the USB-C male rear, full PIN design.
The support frame under the fill light is made of metal, and there are fixing clips on both sides, which is not easy to fall off and emphasizes at the same time
The clip is used by manually squeezing and opening.
The top fill light is rotatable, and the rotation angle is also large, which is convenient for users to adjust to get the best fill light effect.
There are color temperature selection buttons and brightness selection buttons at the top of the fill light.
The Insta360 Flow is powered by the ChargerLab Power-Z KT002 and the input power is about 052w。
Finally, the brightness and light color scene display of the Insta360 Flow fill light is displayed, and the picture above shows the measured scene of the three brightness levels of the fill light.
The three light color scenes of cold light, mixed light, and warm light are as above.
After watching the unboxing and display of the Insta360 Flow fill light, let's disassemble it and take a look at the internal design and materials.
Start by priing the hood along the joint between the diffuser and the housing.
The inside of the fill light is provided with a lighting panel, and the two sides are fixed by screws. The light board welds two rows of LED lights, including 9 cold light + 9 warm light, a total of 18 LED lights, and the cold and warm colors are staggered.
Unscrew the fixing screws on both sides of the light board, take out the light board, and weld the red and black wires on the light board for power supply.
On the back of the light board, two SMD buttons, an MCU and a synchronous step-down circuit are welded.
The main MCU is from Chipsea Technology, model CS32L010F8, which is a 32-bit low-power MCU with M0 core, with a maximum operating frequency of 24MHz, built-in 64KB flash memory and 4KB SRAM, and is packaged in QFN20 for fill light brightness and color temperature control.
A step-down chip from Xinyuan Semiconductor, model MP1605, is a synchronous step-down converter with 2A output current, the chip has a built-in switch tube, and supports 55V input voltage, support 100% duty cycle, support output discharge and short circuit protection.
The micro-motion button is applied with high-temperature tape, which is convenient for the mounter to extract.
A list of all dismantling and a family photo.
The Insta360 Flow Mobile Gimbal Fill Light comes with a Type-C power supply cable, which can be fixed to the phone clip by clipping, and is powered by connecting to the Gimbal's built-in Type-C power supply port. The fill light has built-in RA95 high color rendering lamp beads, with three brightness levels and three color temperature options to meet the needs of different scenarios.
Through the dismantling of the charging head network, it was learned that this fill light is designed with a combination of cold light beads and warm light beads, and a total of 18 lamp beads are staggered. The fill light is equipped with Xinhai Technology CS32L010F8 MCU for brightness and color temperature control, and uses Xinyuan Semiconductor MP1605 synchronous step-down chip. The interior of the fill light is compact and functional.