The principle of APC company belongs to the American power conversion company, which is the earliest UPS power supply to enter China, APC
The product is a product specially developed for Chinese companies, this UPS power supply is a modular design, inside is a large whole module, under the module is the battery pack, you can put the battery, the design is relatively novel, the quality is stable, APC SUVTP15KVA can also be connected to an external battery, the DC voltage of the external battery is 384V, that is to say, 32 batteries are connected in series, and the next time it is connected must be a multiple of 32 batteries.
APC UPS Power Supply Maintenance SUVTP15KVA Modular Pure ** Power Supply Technical Detailed Parameters.
Output. Output power capacity.
12.0 k wattage 150 kva
Maximum configurable power (watts).
12.0 k wattage 150 kva
Rated output voltage.
400v 3ph
Output voltage annotation.
Configurable for or 415 V 3-phase rated output voltage.
Efficiency at full load.
The output voltage is distorted.
Less than 5% at full load
Output frequency (synchronized with the main frequency).
47 - 53 Hz (50 Hz nominal).
Output frequency (out of sync).
50hz +/- 0.1%, rated at 50Hz
Other output voltages.
Load peak factor.
Topology. Double-conversion online.
Waveform type. Sinusoid. Maximum output current.
Output connection. 1) Hard wire 5-wire (3ph + n + g) (battery backup).
1) Screw terminals
1) Hard wire 4-wire (3ph + g) (battery backup).
Bypass. Built-in maintenance bypass, built-in static bypass.
Input. Rated input voltage.
400v 3ph
Enter the frequency. 40 - 70 Hz (auto-sensing).
Enter the terminal type.
hard wire 5-wire (3ph + n + g)
Operating voltage range.
304 – 477 v
Efficiency at full load.
Other input voltages.
Maximum input current.
21.0 a
Input power factor at full load.
Battery vs. runtime.
Battery type. VRLA comes with a pre-installed battery.
Typical charging time.
5 hours. Rated battery voltage.
192 V (neutral reference voltage for grouped cells).
Empty battery slot. Number of RBCs.
Auto-detectable, scalable latency.
Volt-ampere capacity of the battery.
Batteries are optional.
apc-smart-ups-vt-15kva-400v-3-4-5x8-
The battery voltage discharge ends.
154 V runtime. View the uptime chart.
View the uptime chart.
Communications & Management.
Interface ports(s).
db-9 rs-232 , smart-slot
Control wheel. Multifunction LCD status management console.
Audible alarm. audible and visible alarms prioritized by severity
Emergency shutdown. Yes. Physical parameters.
High. 1499 , 149.9 cm
Wide. 559 , 55.9 cm
Deep. 813 , 81.3 cm
Net weight. 506.82 kg
Gross weight. 537.73 kg
Shipping height. 1643 , 164.3 cm
Shipping width. 650 , 65.0 cm
Shipping depth. 1062 , 106.2 cm
Color. black
The number of products on each shipping pallet.
Environment. Operating temperature.
0 - 40 °c
Operating relative humidity.
Operating height. 0-999.9 meters.
Storage temperature. 50 - 40 °c
Store at relative humidity.
Storage height. 0-15000 meters.
Noise that can be heard from 1 meter away from the surface of the device.
64.0 dba
* Heat dissipation. 2170.0 btu/hr
Degree of protection. IP 20 compliance.
Governing Body Certification.
c-tick, ce, en 50091-2, en/iec 62040-3, iec 61000-3-2, iec 61000-3-3, iso 14001, iso 9001, vfi-ss-111
Standard warranty. 1 year repair or replacement service, start-up service.
SUVTP15KH3B4S Features:
APC's Smart-UPS VT, 15KVA, 400V, with 3 battery modules (expandable to 4), 5x8 power-on service, internal maintenance bypass, with paralleling capability.
o Parallelism.
Increase the total power capacity by using multiple uninterruptible power supplies at the same time.
o Ability for parallel redundancy.
Connected devices are powered by multiple uninterruptible power supplies to increase system redundancy.
Smart-UPS VT Features & Benefits.
Marketing features. Input power factor correction.
Installation costs are kept to a minimum by using small generators and wire connections.
Network management. Remote power management for UPS is realized through the network.
Manual maintenance bypass.
There is no need to install an external mechanical bypass, which reduces installation costs.
Dual power inputs.
Connecting the UPS to two separate power sources increases reliability.
Scalable uptime.
Allows for the rapid addition of more run time when needed.
Hot-swappable batteries.
Ensure a clean, uninterrupted power supply to protect the device throughout the battery replacement process.
System protection. Cold start capability.
Provides temporary battery power when the mains power is off.
Certified by a security agency.
Products are tested and certified to ensure they can be used with connected service provider equipment within a defined environment.
Work together safely.
Frequency and voltage adjustment.
Poor frequency and voltage conditions can be corrected without the use of batteries, providing a higher level.
Usability. Total cost of ownership.
Intelligent battery management.
Get the best battery performance, longevity and reliability with smart, precise charging technology.
Manual maintenance bypass.
There is no need to install an external mechanical bypass, which reduces installation costs.
Temperature-compensated battery charging.
Adjust the charging voltage according to the actual battery temperature to extend the battery life.
Input power factor correction.
Installation costs are kept to a minimum by using small generators and wire connections.
Manageability. Compatible with INFINAIR Manager.
for centralized management via APC's INFINAIR Manager software.
Network management. Remote power management for UPS is realized through the network.
Audible alarm. Provide notification of changes in mains and UPS power conditions.
LSD display.
Alphanumeric display showing system parameters and alarms.
LED status indicator.
With the help of the ** indicator, you can quickly understand the device and power status.
Programmable frequency range.
Guaranteed compatibility with different input frequencies.
SmartSlot slots.
Customize UPS performance with management cards.
Serviceability. Automatic self-test.
Self-check the battery regularly to ensure early detection of batteries that need to be replaced.
Replace the battery without tools.
The battery can be replaced quickly and easily.
Modular design.
Self-diagnostics, field-replaceable modules provide fast availability and reduce maintenance requirements.
The module is installed and ready to ship.
Capable of segmented shipping and testing of pre-installation UPS as well as rapid installation.
Usability. Parallel battery modules.
Higher availability through redundant batteries.
Automatic internal bypass.
Provides utility power to the connected load in the event of an overload or failure of the UPS power supply.
Generator compatible.
When using generator power, ensure a clean, uninterruptible power supply to protect the equipment.
Hot-swappable batteries.
Ensure a clean, uninterrupted power supply to protect the device throughout the battery replacement process.
Scalable uptime.
Allows for the rapid addition of more run time when needed.
Dual power inputs.
Connect the APC UPS power supply into two separate power supplies for added reliability.